LINEAR TECHNOLOGY V ITC, No. 07-1572 (Fed. Cir. 2008)

Annotate this Case

Download PDF

NOTE: This disposition is nonprecedential. United States Court of Appeals for the Federal Circuit 2007-1572 LINEAR TECHNOLOGY CORPORATION, Appellant, v. INTERNATIONAL TRADE COMMISSION, Appellee, and ADVANCED ANALOGIC TECHNOLOGIES, INC., Intervenor. Mark G. Davis, Weil, Gotshal & Manges LLP, of Washington, DC, argued for appellant. With him on the brief was Ronald J. Pabis. Of counsel on the brief were Natalia V. Blinkova, Amalie M. Weber, and Patricia E. Chow, McDermott, Will & Emery LLP, of Washington, DC. Of counsel were Jimmy M. Shin, McDermott, Will & Emery LLP, of Palo Alto, California, and Matthew G. Cunningham, of Washington, DC. Paul M. Bartkowski, Attorney, Office of the General Counsel, United States International Trade Commission, of Washington, DC, argued for appellee. With him on the brief were James M. Lyons, General Counsel, and Wayne W. Herrington, Assistant General Counsel. Of counsel was Eric Frahm, Attorney-Advisor. Andrew N. Thomases, Dechert LLP, of Mountain View, California, argued for intervenor. With him on the brief were Chris Scott Graham and Philip Barilovits. Of counsel were Jonathan Daniel Baker, Anthony B. Diepenbrock, III and Ayumi Urabe, of Mountain View, California, and Stephen J. Rosenman, of Washington, DC. Appealed from: United States International Trade Commission NOTE: This disposition is nonprecedential. United States Court of Appeals for the Federal Circuit 2007-1572 LINEAR TECHNOLOGY CORPORATION, Appellant, v. INTERNATIONAL TRADE COMMISSION, Appellee, and ADVANCED ANALOGIC TECHNOLOGIES, INC., Intervenor. On appeal from the United States International Trade Commission in Investigation No. 337-TA-564. _________________________ DECIDED: August 28, 2008 _________________________ Before MAYER, LOURIE, and SCHALL, Circuit Judges. SCHALL, Circuit Judge. DECISION Linear Technology Corp. ( Linear ) filed a complaint with the United States International Trade Commission ( the Commission ) under section 337 of the Tariff Act of 1930, 19 U.S.C. § 1337(a)(1)(B), alleging that Advanced Analogic Technologies, Inc. ( AATI ) imported and/or sold for importation certain electronic charge pump DC/DC converter devices that infringed United States Patent No. 6,411,531 ( the 531 patent ). See 71 Fed. Reg. 14545 (Int l Trade Comm n March 22, 2006) (Notice of Investigation). Linear now appeals the Commission s final determination (1) that AATI s imported AAT3113, AAT3141, and AAT3151 devices did not infringe asserted claims 4, 9, or 26 of the 531 patent; (2) that AATI s imported AAT3119 device did not infringe claim 9 of the 531 patent; 1 (3) that Linear failed to satisfy the domestic industry requirement of section 337; (4) that claims 4 and 26 of the 531 patent were invalid as anticipated by U.S. Patent No. 5,132,895 ( the 895 patent ) to Kase; and (5) that claims 4, 9, and 26 of the 531 patent were invalid as anticipated by U.S. Patent No. 5,680,300 ( the 300 patent ) to Szepesi. Because substantial evidence supports the Commission s determination that claims 4, 9, and 26 of the 531 patent are invalid as anticipated by the 300 patent, we affirm. DISCUSSION I. The 531 patent is entitled Charge Pump DC/DC Converters with Reduced Input Noise. A charge pump DC/DC converter is a power supply circuit that provides a regulated output voltage to a load from an input voltage source. 531 patent col.1 ll.9 11. The 531 patent is directed at a particular type of charge pump DC/DC converter that uses switches to alternately charge and discharge an intermediate storage capacitor. The concept of switching converters was well known at the time the application for the 531 patent was filed. However, prior art switching converters had the disadvantage of noise induced on the input voltage source due to fluctuations or 1 AATI did not contest the direct infringement of claims 4 and 26 by the AAT3119. 2007-1572 2 variations in the current drawn by the converter. Id. col.1 ll.17 20. The invention of the 531 patent was intended to reduce noise on the input voltage source by maintaining a substantially constant input current. Id. col.1 ll.36 48. Claim 4, and claim 1 from which it depends, are reproduced below. 1. A method for regulating a voltage at an output node of a boost voltage regulator, the method comprising: providing a first capacitor; providing a first switch coupled between the first capacitor and the output node; providing a second switch coupled to the first capacitor; controlling the first and second switches to alternately charge the first capacitor from an input voltage and discharge the first capacitor to the output node; monitoring the voltage at the output node to generate a control signal; and controlling the current flowing through the first capacitor in response to the control signal when the first switch is closed. 4. The method of claim 1 further comprising: controlling the current through the first capacitor in response to the control signal when the second switch is closed. Although written in independent form, claim 9 is identical to claim 4, except that it specifically provides that the step recited in the final limitation is performed by providing a variable resistance in series between the input voltage and the first capacitor when the second switch is closed. Claim 26, and claim 23 from which it depends, are reproduced below. 23. A boost voltage regulator that regulates a voltage at an output node, comprising: a first capacitor; 2007-1572 3 a first switch coupled between the first capacitor and the output node; a second switch coupled to the first capacitor, wherein current alternately flows from an input voltage to the first capacitor and from the first capacitor to the output node; feedback loop circuitry that monitors the voltage at the output node and generates a control signal; and a transistor that controls the current flowing through the first switch in response to the control signal when the first switch is closed. 26. The regulator of claim 23 wherein: the transistor controls the current through the second switch in response to the control signal when the second switch is closed. Before the presiding administrative law judge ( ALJ ), the parties disputed whether the term voltage regulator in the preamble of claims 4, 9, and 26 should be regarded as a claim limitation. The ALJ concluded that voltage regulator is a limitation because it gives meaning to all of the asserted claims. In re Certain Voltage Regulators, Inv. No. 337-TA-564, slip op. at 30 31 (Int l Trade Comm n May 22, 2007) ( ALJ Initial Determination ) (citing In re Paulsen, 30 F.3d 1475, 1479 (Fed. Cir. 1994)). The parties also disputed the appropriate construction of voltage regulator in the event that it was determined to be a claim limitation. Relying upon the 531 patent s specification as well as extrinsic evidence, the ALJ construed voltage regulator as a device that continuously maintains a constant output voltage at a predetermined, specified target value regardless of changes in input voltage or load current, so long as input voltage and load current are within the specified operating range for the device. 2 Id. at 33 35. 2 The parties agree that a proper construction of voltage regulator, if it is a claim limitation, does not depend on the operating range i.e., range of input voltages 2007-1572 4 With respect to infringement, the ALJ determined that AATI s devices did not have an output voltage that was predetermined and constant. Id. at 65 68. Rather, the ALJ observed that tests performed by AATI s expert, Dr. Szepesi, demonstrated that the devices have output voltages that vary greatly with changes in input voltage and load current. Id. at 66. Thus, the ALJ concluded that AATI s devices did not satisfy the voltage regulator requirement of the asserted claims. Likewise, the ALJ determined that Linear did not satisfy the domestic industry requirement of section 337 because its own device the LTC3202 did not provide a constant, regulated output voltage over its specified range of operation. Id. at 111 14. Finally, the ALJ concluded that claims 4, 9, and 26 of the 531 patent were invalid as anticipated by both the 895 and 300 patents. Id. at 92 97. On appeal, the Commission determined to review the sole issue of whether asserted claim 9 of the 531 patent was anticipated by the 895 patent to Kase. 72 Fed. Reg. 41774, 41775 (Int l Trade Comm n July 31, 2007) (Notice of Review). The Commission ended up taking no position on that issue, however, effectively vacating the ALJ s determination that claim 9 of the 531 patent was anticipated by the 895 patent. Id. The remainder of the ALJ s rulings with respect to the 531 patent were not reviewed and thereby became part of the Commission s final decision. See 19 C.F.R. § 210.42(h). and output currents that is specified on a device s datasheet or box specification. Therefore, although it is not entirely clear what was meant by the term specified operating range, we do not interpret the Commission s construction of voltage regulator as being tied to the range of input voltages and output currents set forth on a device s datasheet or box specification. We agree with the parties that such a construction of voltage regulator would not be correct. 2007-1572 5 II. On appeal, Linear argues that the Commission s claim construction was erroneous. Linear contends that the preamble term voltage regulator is not a limitation of the asserted claims, and that the Commission misconstrued voltage regulator even if it is determined to be a claim limitation. In addition, Linear argues that the Commission s factual determinations regarding infringement, domestic industry, and anticipation are not supported by substantial evidence. With respect to claim construction, Linear first contends that the preamble term voltage regulator is not a limitation of the asserted claims. According to Linear, a preamble term is limiting if (1) the preamble provides an antecedent basis for a term in the body of the claim, C.R. Bard, Inc. v. M3 Sys., Inc., 157 F.3d 1340, 1350 (Fed. Cir. 1998), or (2) there is clear reliance on the preamble during prosecution to distinguish the invention from the prior art, Intirtool, Ltd. v. Texar Corp., 369 F.3d 1289, 1295 (Fed. Cir. 2004). Linear contends that neither is the case here. In addition, Linear argues that the Commission misconstrued voltage regulator even if it is a claim limitation. According to Linear, the Commission s construction improperly relies upon the operating range i.e., the range of input voltages and output currents specified on a device s accompanying datasheet or box specification. Linear explains that the claims, specification, and prosecution history of the 531 patent do not refer to datasheets. In addition, Linear contends that a potential infringer could avoid liability under the Commission s construction merely by changing the numbers listed on its product s datasheet. According to Linear, a skilled artisan reading the specification would understand a voltage regulator to denote a circuit topology capable 2007-1572 6 of delivering a predetermined output voltage under appropriate conditions. Linear further argues that the predetermined output voltage need not be a single, fixed, constant voltage. Rather, a skilled artisan would understand that it may be desirable to design a circuit that provides varying voltage outputs. With respect to anticipation of the asserted claims, Linear argues that two limitations are not disclosed in the 300 patent. First, Linear briefly contends that the circuit disclosed in the 300 patent is not a voltage regulator under the Commission s narrow construction because AATI cannot prove that it necessarily provides a single output voltage throughout its operating range. Second, Linear argues that the 300 patent does not disclose control of the circuit s input current during both phases of the charge pump cycle i.e., during both charging and discharging of the intermediate capacitor. 3 According to Linear, the 300 patent only discloses control of input current during the discharge phase. Finally, Linear also contends that the Commission s determinations regarding anticipation by the 895 patent, infringement, and domestic industry are not supported by substantial evidence. Because we affirm based upon anticipation by the 300 patent, however, we need not reach these additional issues. III. Anticipation is a question of fact. Gen. Elec. Co. v. Nintendo Co., Ltd., 179 F.3d 1350, 1353 (Fed. Cir. 1999). We review the Commission s factual findings under the substantial evidence standard. 19 U.S.C. § 1337(c); 5 U.S.C. § 706(2)(E). Thus, we review for substantial evidence the Commission s determination that claims 4, 9, and 26 3 Claims 4, 9, and 26 of the 531 patent require control of input current during both the charge and discharge phases of the charge pump cycle. 2007-1572 7 of the 531 patent are anticipated by the prior art 300 patent. Substantial evidence is such relevant evidence as a reasonable mind might accept as adequate to support a conclusion. Enercon GmbH v. Int l Trade Comm n, 151 F.3d 1376, 1381 (Fed. Cir. 1998) (quoting Consol. Edison Co. v. Nat l Labor Relations Bd., 305 U.S. 197, 229 (1938)). It is more than a mere scintilla, Consol. Edison, 305 U.S. at 229, but something less than the weight of the evidence, Consolo v. Fed. Maritime Comm n, 383 U.S. 607, 619 20 (1966). Importantly, the possibility of drawing two inconsistent conclusions from the evidence does not prevent an administrative agency s finding from being supported by substantial evidence. Id. (citation omitted). The first step in any invalidity analysis is claim construction, an issue of law this court reviews de novo. Akamai Techs., Inc. v. Cable & Wireless Internet Services, Inc., 344 F.3d 1186, 1192 (Fed. Cir. 2003) (citing Cybor Corp. v. FAS Techs., Inc., 138 F.3d 1448, 1456 (Fed. Cir. 1998) (en banc)). Here, however, we need not engage in a lengthy discussion regarding how voltage regulator should be construed i.e., whether voltage regulator is a limitation of the asserted claims and, if so, the meaning of that term. That is because substantial evidence supports the conclusion that the 300 patent discloses a voltage regulator under all proposed constructions even the more restrictive construction adopted by the Commission. 4 The 300 patent is entitled Regulated Charge Pump DC/DC Converter (emphasis added). The preferred embodiment uses four switches to achieve the voltage conversion, by alternately charging and discharging an intermediate storage 4 Of course, we would not need to consider whether the 300 patent discloses a voltage regulator if the preamble term voltage regulator is not a limitation of the asserted claims. 2007-1572 8 capacitor. The patent instructs that at least one of the switches functions as a variable resistor, wherein the resistance is modulated via feedback as a function of the output voltage. 300 patent col.3 ll.20 37. The feedback/modulation scheme is designed to regulate the output voltage at a useful, predetermined value. See id. col.3 ll.41 45 ( The new charge pump voltage converter can be used in electronic processing systems to accept power at a standard voltage from a power source and convert it to another voltage for use by circuits which require non-standard voltage . . . . ). Further, when the patent describes regulating the output voltage, it is clearly referring to maintaining the output voltage at a single value despite certain fluctuations in the input voltage and/or output current. Id. col.2 ll.14 17. Thus, we conclude that the 300 patent discloses a voltage regulator, even under the Commission s more restrictive interpretation requiring a constant output voltage at a predetermined, specified target value regardless of changes in input voltage or load current. 5 ALJ Initial Determination at 35. By extension, the disclosure of the 300 patent also meets the broader definition of voltage regulator advanced by Linear, under which the predetermined output voltage need not be a single, fixed, constant voltage. In addition, we conclude that substantial evidence supports the Commission s determination that the 300 patent discloses control of input current during both phases of the charge pump cycle. Figure 3 of the 300 patent depicts an embodiment of the inventive voltage converter. 5 Prior art patents are presumed enabling for purposes of anticipation, including both claimed and unclaimed material. Amgen Inc. v. Hoechst Marion Roussel, Inc., 314 F.3d 1313, 1354 55 (Fed. Cir. 2003). Although the presumption may be overcome with evidence to the contrary, Linear has made no attempt to present such evidence here. 2007-1572 9 Referring to Figure 3, four switches SW1, SW2, SW3, and SW4 are used to achieve the voltage conversion. Switch drivers SD1, SD2, and SD3 control the operation of the four switches. During the first phase of the clock Î¸1 (the charge phase), SD1 drives SW2 and SW3 to an on state, while SD2 drives SW1 to an off state and SD3 drives SW4 to an off state. 300 patent col.5 ll.28 32. During the second phase of the clock Î¸2 (the discharge phase), SD1 drives SW2 and SW3 to an off state, while SD2 drives SD1 to an on state and SD3 provides SW4 with a modulated drive voltage. Id. col.5 ll.28 39. The level of the modulated drive voltage provided by SD3 is a function of the output voltage VLOAD, thereby enabling regulation of the output voltage via feedback. Linear concedes that this modulation of SW4 s drive voltage as a function of output voltage satisfies the limitation of the asserted claims requiring control of input current during the discharge phase. It argues, however, that the 300 patent does not disclose control of input current during both the charge and discharge phases, as required by the asserted claims of the 531 patent. In other words, Linear contends that 2007-1572 10 the 300 patent does not disclose a circuit wherein the drive voltage to SW2 and/or SW3 is modulated during the charge phase and the drive voltage to SW1 and/or SW4 is modulated during the discharge phase. We do not agree. First, like the Commission, we note the statement in the specification that although in the embodiments disclosed the switches SW1, SW2 and SW3 are conventionally driven, and the switch SW4 is driven in response to feedback from the charge pump output, any of the switches SW1, SW2, SW3 or SW4 may be driven in response to feedback from the output. Id. col.7 ll.30 35 (emphasis added). From this statement, it is clear that the 300 patent expressly indicates that input current may be controlled during the charge phase (by modulating SW2 or SW3) as well as the discharge phase (by modulating SW1 or SW4). Linear contends, though, that this statement is inapposite because, by using the disjunctive term or, the patent merely indicates that any one of SW1 SW4 may be modulated, not that multiple switches may be modulated. Thus, Linear argues that the statement merely discloses control of input current during the charge phase or the discharge phase, not both phases. In fact, Linear argues that modulating more than one switch would be contrary to the patent s stated goal of saving charge pump space, as it would require replication of the SD3 feedback/modulation circuitry. Contrary to Linear s argument, however, we note that the 300 patent does not teach away from modulating multiple switches within the same circuit design. Indeed, it expressly provides in the discussion of Figure 3: In the illustrated preferred implementation only one switch, SW4, is modulated in the fashion described in relation to switch driver SD3 16 of FIG. 3. However, SW1 and SW4 may both be driven in such a 2007-1572 11 manner, or SW1 alone may be driven in that fashion. Id. col.5 ll.20 24 (emphasis added). Linear responds that switches SW1 and SW4 are both active during the discharge phase of the charge pump cycle. Thus, according to Linear, the fact that the patent discloses modulation of SW1 and SW4 does not necessarily mean that it discloses modulation during both phases of the charge pump cycle. Regardless, we think that at a minimum the patent s disclosure that both SW1 and SW4 may be modulated contradicts Linear s arguments (1) that the disjunctive use of or in column 7 indicates that only one of the four switches may be modulated and (2) that modulating multiple switches would violate the patent s purported goal of saving space. See also id. col.3 ll.17 40 (stating that at least one of the switches is driven with a modulated signal), claims 1 22 (same). Any further ambiguity with respect to the statement in column 7 is resolved by the patent s discussion of Figure 1. The Detailed Description of the Invention of the 300 patent begins with a discussion of Figure 1, shown below. Figure 1 is a block diagram that illustrates the switch controller of the patented invention i.e., the basic components used to control the operation of the switches. Id. 2007-1572 12 col.4 ll.9 10. The patent instructs that in the typical arrangement, SD3 provides a modulated drive signal to one of the switches (e.g., SW4 in Figure 3), and the remainder of the switches are conventionally driven by SD1 and SD2. See id. col.4 ll.9 43. Accordingly, only SD3 is depicted in Figure 1 as containing the additional circuitry required for switch modulation i.e., feedback block 18, modulation block 20, and synchronization block 22. The patent also expressly states, however, that the typical arrangement of switches and switch drivers may be modified. Furthermore, additional switch drivers SD4 17 like SD3 16 could be employed during any of the clock phases Î¸1 Î¸n to provide additional modulated drive signals. However, for the sake of clarity, further FIG.s, and discussions related to those FIG.s, will illustrate two-phase implementations which employ one modulated switch driver such as switch driver SD3 16. Id. col.4 ll.44 49 (emphases added). In other words, after describing the modulated drive signal provided by SD3, the patent states that any of the other switch drivers, including SD4, may be modified to provide additional modulated drive signals in the same manner as SD3. We think that the word additional conveys an understanding that both SD4 and SD3 may be modulated within the same circuit design. At a minimum, the Commission s interpretation of the passage in that way, see ALJ Initial Determination at 96 97, was not unreasonable. Further, Figure 1 depicts SD4 and SD3 as being active during the charge (Î¸1) and discharge (Î¸2) phases, respectively. Therefore, we conclude that the 300 patent particularly Figure 1 and its accompanying text may be reasonably interpreted as disclosing control of input current during both the charge and discharge phases of the charge pump cycle. 6 6 In its reply brief, Linear contends that AATI s citation to the 300 patent col.4 ll.44 49 is a newly-crafted argument that should not be considered because it is being raised for the first time on appeal. We note, however, that Dr. Szepesi was 2007-1572 13 Because substantial evidence supports the Commission s determination that claims 4, 9, and 26 are anticipated by the 300 patent, we affirm. clearly questioned about the passage at the hearing before the ALJ, and he stated that it supported his opinion that the 300 patent discloses control of input current during both phases of the charge pump cycle. Yes, it teaches two things, one, that there clearly can be more than one modulated switch driver. It also teaches that these modulated switch drivers can be on different phases, so one can be maybe on the charge phase, and one can be [on the] released charge phase or more of them, it clearly discloses there can be any phases and any number of them. Hearing Tr. at 1377. In addition, both the passage and Dr. Szepesi s testimony about it were cited in the ALJ s discussion of anticipation with respect to the 300 patent. ALJ Initial Determination at 96 97. 2007-1572 14

Some case metadata and case summaries were written with the help of AI, which can produce inaccuracies. You should read the full case before relying on it for legal research purposes.

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.